Skip to main content

XTM Cloud 13.4

Leveraged matches

To access the Leveraged matches parameters, select Configuration > Settings > Translation > TM > Leveraged matches.

To make changes to the Leveraged matches settings, select the relevant option for the required parameters and then, select the Save button at the bottom of the screen.

Table 16. Leveraged matches parameters

Parameter

Description

Search only if there are no ICE matches

By default, if there is an ICE match, XTM Cloud does not search for a 100% leveraged match for the relevant segment. You can change this behavior by clearing the checkbox.

Show leveraged matches

You can decide if and when 100% leveraged matches are displayed to Linguists in XTM Workbench:

  • Yes – 100% leveraged matches are always displayed to Linguists.

  • Only if its approval status is higher that the ICE match

  • Only if its XLIFF:doc status is higher than the ICE match – This option is available if the TIPP parameter has been enabled (for details, see General system settings).

  • Only if its approval and XLIFF:doc statuses are higher than the ICE match – This option is available if the TIPP parameter has been enabled (for details, see General system settings).

  • No – 100% leveraged matches are never displayed to Linguists.

Populate target with match

You can decide when a 100% leveraged match is automatically inserted into the target segment. The options are:

  • Always, fixing inline differences

  • Only if inline tags are the same

  • Never

Number of matches to display

You can set a maximum number of 100% leveraged matches which are displayed in XTM Workbench, in the Matches docked panel for a single segment. The options are:

  • 1

  • 2

  • 3 (default)

  • 4

  • 5

Save context of leveraged matches in TM when automatically set to done

If you select this option, when a 100% leveraged match is automatically set to Completed, it will be saved with context information. The result of this is that in future projects, you should get an increased percentage of ICE matches.

Note

This parameter is enabled or disabled for the entire system and so either used or not used for all customers and in all projects.

Set leveraged matches from approved TM to done

XTM Cloud can automatically set 100% leveraged matches from approved TM to Completed during project analysis without the need to confirm them in XTM Workbench. This setting will only apply for an active segment in an active workflow step, if the target segment (which has been promoted to the 100% leveraged match, while the Linguist was working in XTM Workbench) is populated automatically. If a Linguist manually selects a 100% leveraged match from the Matches docked panel, this setting will not apply.

You can decide if this parameter is available at customer and project level and specify the default. To do so, use the checkbox in the Permit column:

  • Selected – This parameter is displayed at customer level, in project templates and when creating a project.

    If you also select the checkbox in the Default setting column, the parameter will be enabled at customer and project level by default. Project Managers can disable it, if required.

    Additionally, use radio buttons to specify in which workflow steps should these segments be set to done (Completed):

    • All except last step – XTM Workbench sets the status of segments with 100% leveraged matches from approved TM to Completed in all workflow steps except the last one.

    • First step only – XTM Workbench only sets the status of segments with 100% leveraged matches from approved TM to Completed in the first workflow step.

    • All steps – XTM Workbench sets the status of segments with 100% leveraged matches from approved TM to Completed in all workflow steps.

  • Cleared (default) – This parameter is NOT displayed at customer and project level.

Set leveraged matches from not approved TM to done

XTM Cloud can automatically set a 100% leveraged matches from not approved TM to done during project analysis without the need to confirm them in XTM Workbench. This setting will only apply for an active segment in an active workflow step, if the target segment (which has been promoted to the 100% leveraged match, while the Linguist was working in XTM Workbench) is populated automatically. If a Linguist manually selects a 100% leveraged match from the Matches docked panel, this setting will not apply.

You can decide if this parameter is available at customer and project level and specify the default. To do so, use the checkbox in the Permit column:

  • Selected – This parameter is displayed at customer level, in project templates and when creating a project.

    If you also select the checkbox in the Default setting column, the parameter will be enabled at customer and project level by default. Project Managers can disable it, if required.

    Additionally, use radio buttons to specify in which workflow steps should these segments be set to done:

    • All except last step – XTM Workbench sets the status of segments with 100% leveraged matches from not approved TM to done in all workflow steps except the last one.

    • First step only – XTM Workbench only sets the status of segments with 100% leveraged matches from not approved TM to done in the first workflow step.

    • All steps – XTM Workbench sets the status of segments with 100% leveraged matches from not approved TM to done in all workflow steps.

  • Cleared (default) – This parameter is NOT displayed at customer level, in project templates and when creating a project.